3c351ee6

16:14. Back door

Back door

 
1 – cover of the internal handle;
2 – internal handle of opening of a door;
3 – internal finishing;
4 – door upholstery;
5 – arm of the internal handle of a door;
6 – door upholstery arm;
7 – internal handle of a door assembled;
8 – pylevlagozashchitny film;
9 – exterior finish;
10 – external slip;
11 – glass;
12 – the directing glass sealant;
13 – the guide flew down;
14 – window regulator;
15 – door lock;
16 – external handle of opening of a door;
17 – door hinge;
18 – limiter of opening of a door;
19 – moisture protective consolidation of a door;
20 – shock plate

Removal

PERFORMANCE ORDER
1. Remove moisture protective consolidation of a door.
2. Remove a door upholstery.
3. Turn out one screw of fastening of an arm of the internal handle of opening of a door.
4. Remove the internal handle of unlocking of the lock of a door in the following order:
      a. turn out three screws of fastening of the handle;
      b. disconnect two drafts from the handle;
      c. remove the internal handle of a door.
5. Remove a pylevlagozashchitny film, gradually separating it from a door frame.
6. Remove glass in the following order:
      a. repeatedly connect the switch of management of a window regulator;
      b. connect a wire to the negative plug of the rechargeable battery;
      c. include ignition and move glass to half-open situation;
      d. switch off ignition;
      e. turn out two bolts of fastening of glass to a window regulator;
      f. inclining and lifting a back part, remove glass from the outer side of a door;
      g. disconnect a wire from the negative plug of the rechargeable battery.
7. Disconnect the socket of a plait of wires.
8. Through an opening in the internal panel of a door turn out two nuts of fastening of the external handle of a door.
9. Remove the external handle of a door.
10. Turn out three screws of fastening of the lock of a door.
11. Through an opening in the internal panel of a door remove the door lock.
12. Disconnect the electric socket of the engine of the drive of a window regulator.
13. Turn out six nuts of fastening of a window regulator.
14. Through an opening in the internal panel of a door remove a window regulator.
15. Disconnect the electric socket and a clip of its fastening from the modulator.
16. Through an opening from hinges extend a plait of wires from a door.
17. Remove a glass guide.
18. Remove an external moisture protective strip.
19. Remove an external slip from a door.
20. Remove the limiter of opening of a door in the following order:
      a. turn out a bolt of fastening of the limiter of opening of a door;
      b. through an opening in the internal panel of a door remove the limiter of opening of a door.
21. Remove a pylevlagozashchitny strip.
22. Turn out bolts of fastening of both hinges and remove a door from the car.

Installation

PERFORMANCE ORDER
1. Establish a door in the following order:
      a. install properly a door on the car;
      b. screw bolts of fastening of both hinges.

Inhaling moment: 17–29 N • m
2. Establish moisture protective consolidation of a door.
3. Install the limiter of opening of a door in the following order:
      a. through an opening install the limiter of opening of a door in the internal panel of a door;
      b. screw a bolt of fastening of the limiter of opening of a door.

Inhaling moment: 22–27 N • m
4. Establish an external overlay for a door.
5. Establish an external moisture protective strip.
6. Establish a glass guide.
7. From hinges of a door pass a plait of wires throughout a door.
8. Connect the modulator socket.
9. Establish a window regulator into place.
10. Screw six nuts of fastening of a window regulator.

Inhaling moment: 9–13 N • m
11. Connect the window regulator engine socket.
12. Put the door lock through an opening in the internal panel of a door.
13. Fix the door lock by three screws.
14. Install the external handle of a door.
15. Fix by two nuts the external handle of a door.

Inhaling moment: 9–13 N • m
16. Connect thirsts of the lock for the external handle of a door.
17. Establish a glass guide in the following order:
      a. install a glass guide through an opening in the internal panel of a door;
      b. fix by a bolt directing to glasses.

Inhaling moment: 9–13 N • m
18. Establish glass in the following order:
      a. for lubricant at installation of glass use soap solution;
      b. insert outside of a door at first a forward part of glass, then, turning and lowering, establish glass at a door and arrange it on a window regulator arm.
19. Tighten two bolts of fastening of glass.
      
Inhaling moment: 2–3 N • m
20. If necessary, adjust the provision of glass.
21. Establish a pylevlagozashchitny film on a door and bring drafts of the internal handle of opening of the lock of a door out of a pylevlagozashchitny film.
22. Install the internal handle of a door in the following order:
      a. connect two drafts of the lock of a door to the handle;
      b. fix the handle by three screws.
      
Inhaling moment: 3–4 N • m
23. Establish an arm of the handle and fix it by one screw.
24. Connect sockets of a plait of wires.
25. Establish a door upholstery.
26. Connect a wire to the negative plug of the rechargeable battery.
27. Move glass in up to an emphasis.