Front and rear bumpers consist of three parts: overlays of a bumper, foamy absorber of energy and amplifier of a bumper.
The slip is made of polypropylene. The foamy absorber of energy is made of expanded polystyrene.
The amplifier of a bumper is manufactured of strong fibers and polypropylene. The foamy absorber of energy is located between an overlay of a bumper and the amplifier.
Illumination of salon
Illumination of salon is intended for illumination of salon when landing in the car when opening doors. Also illumination can be included behind closed doors. The lamp of illumination of salon is located in the center of a ceiling.
The door fastens to a car body two hinges and the limiter of opening of a door. The limiter of opening of a door limits the size of opening of a door.
Hollow rubber consolidation of a door is established on a ledge of a door and prevents penetration of moisture and dust between a door and a body.
Door lock drafts connection with external and internal handles of opening of a door.
The window regulator with the electric drive consists of the window regulator mechanism with the glass fixed on it, a forward guide of glass, the switch installed in an armrest and the plastic frame protecting all components.
The shock plate of the lock of a door can be adjusted for reliable by t of soft closing of a door.
External lighting fixtures
External lighting fixtures consist of six systems of lighting: headlights, lamps of a signal of turn, dimensional lighting, alarm light system, stoplights and lamp of illumination of registration plate (only back part). Lamps of all six systems are located in the left and right headlights, the left and right back lamps, a back top stoplight and two lamps of illumination of registration plate. All lighting eats 12-volt electric system, and are operated by the driver.
Back lamps are executed in such a way that aerodynamically continue a body form. The lens of a lamp has three colors. Back lamps contain three glow lamps. Two lamps – with one thread of an incandescence are also intended for a turn signal / the alarm light system and a backing. The third lamp with two threads of an incandescence is intended for stoplights and dimensional illumination of the Lamp fasten on the plastic holder. The holder of glow lamps acts from within the car for replacement of glow lamps.
The lamp of a stoplight joins the switch installed about a pedal of a brake and put in action when pressing a pedal of a brake.
Lamps of a backing join the switch installed on the transmission. At inclusion of transfer of a backing, contacts of the switch become isolated therefore backing lamps light up.
Turn signal lamps / the alarm light system join the combined switch installed on a steering column. The breaker of indexes of turn / the alarm light system is located under the dashboard on the left side.
Headlights are executed in such a way that aerodynamically continue a body form. The headlight fastens to a body two bolts.
Each headlight contains three glow lamps. One glow lamp of halogen type with two threads of an incandescence serves for driving and passing beam. Ring consolidation is isolated by the holder of the glow lamp to exclude hit in a headlight of moisture and dust. Replacement of a lamp is made from a motor compartment, without removing a headlight. In each headlight adjustment of light is provided in the horizontal and vertical planes. On two adjusting screws are available to each headlight through the openings located over headlights. The internal screw regulates light in the horizontal plane, and external – in vertical.
Two other glow lamps are intended for the index of turn / the alarm light system and dimensional lighting.
Turn signal lamps / the alarm light system join the combined switch installed on a steering column.
Back top stoplight
The plafond of a back top stoplight of red color is also well visible through back glass. The back top stoplight has one lamp. For replacement of a lamp of a back top stoplight it is necessary to remove a cover which fastens two screws. The lamp of a stoplight joins the switch installed about a pedal of a brake and put in action when pressing a pedal of a brake.
Lamp of illumination of registration plate
Two lamps of illumination of registration plate are established in a trunk lid. In each lamp about one lamp is established. Lamps join together inclusion of dimensional lighting. For replacement of a lamp it is necessary to remove the transparent lens who fastens two screws.
The ceiling is made of fabric and serves as a decorative and protective layer between passengers and a roof of the car. Between a ceiling and a roof of the car thermal insulation plates are established. In the center of a ceiling the plafond of internal illumination of salon is established. The ceiling and plates of thermal insulation can be replaced.
The cowl of alligator type which is opening from the forward party of the car and locked the standard double unlocking mechanism. The handle of opening of the lock of a cowl is located on the left side in the bottom of the dashboard. When opening the cowl turns on two hinges and is fixed in open situation by a support. Each hinge fastens two bolts to a body and two bolts to a cowl. For adjustment of provision of a cowl, it can move at the expense of the extended openings for bolts of fastening of hinges of a cowl. The latch of a cowl can be adjusted in two planes for providing optimum position of the lock of a cowl and a shock plate.
The car is equipped with one sound signal established on the center of the car behind a front bumper. Inclusion of a sound signal is carried out by pressing of the button located in the center of a steering wheel. Tension from the positive plug of the rechargeable battery moves on the relay of the sound signal located in the block of safety locks of a motor compartment.
Combination of devices
The combination of devices is intended for informing the driver on the current parameters of the car. The analog electric speedometer, counters of a daily and general run of the car, analog indexes of a reserve of fuel and temperature of cooling liquid are located in a combination of devices.
Control lamps warn about the following:
– low pressure of engine oil;
– shutdown of anti-blocking system of brakes (ABS);
– existence of malfunctions in the engine;
– the heater of back glass is included;
– low level of brake fluid;
– there is no charging of the rechargeable battery;
– the seat belt of the driver is not fastened;
– driving beam of headlights is turned on;
– one of car doors is not closed;
– the parking brake is tightened;
– indication of a safety cushion;
– additional indicator (ACC);
– low level of fuel in the fuel tank;
– indicator of turning on of the alarm light system;
– turn inclusion indicator.
Electric sockets of a combination of devices are located from the back party of the case of a combination of devices which can be disconnected after a vydviganiye of a combination of devices from the dashboard. The printed circuit board is installed on a back part of a combination of devices. Holders of the glow lamp are established in the printed circuit board from the back party of a combination of devices. Indexes can be removed after removal of finishing and glass from a combination of devices.
Indexes and sensors
The index of temperature of cooling liquid is located in a combination of devices and shows temperature if the key in the lock of ignition is in the provision of "ON". Temperature sensor located on the engine changes the resistance depending on temperature.
The electric system of measurement of level of fuel consists of the index of level of fuel, the fuel level sensor located in the fuel tank and connecting wires. The index of level of fuel is located in a combination of devices and shows fuel level if the key in the lock of ignition is in the provision of "ON". At turn of the ignition key in provisions of "ACC" or "LOCK" the index of level of fuel does not work.
The speedometer specifies car speed of time at present. The drive of a speedometer and counters of a daily and general run of the car is carried out by electric motors on the basis of information from sensors.
The tachometer specifies the frequency of rotation of the engine in revolutions per minute. The electronic block of a tachometer measures quantity of the impulses created by the block of ignition and converts them into revolutions per minute.
The switch of a heater of back glass includes defrosting of glass and specifies that defrosting is carried out.
The switch of the alarm light system includes all signals of turn, at the same time indicators of inclusion of turn in combinations of devices also blink.
The switch of external provision of a rear-view mirror allows to regulate movement of the switch the provision of a mirror in the vertical and horizontal planes. The R/L switch allows to choose a mirror which adjustment of situation will be carried out.
The switch of a screen wiper operates work of screen wipers of a windshield.
Control lamps and indicators
Additional control lamps of "ACC" light up when the radio receiver is switched on or other consumer and a key in the lock of ignition is included is in the provision of "ACC".
The control lamp of anti-blocking system of brakes (ABS) lights up when the ABS control unit finds failure in anti-blocking system of brakes.
The control lamp of "BRAKE" lights up when lowering brake fluid below safe level, and the key in the lock of ignition is in the provision of "ON". The sensor of level of brake fluid is located in a popolnitelny tank of the brake system. A float at lowering of the level of brake fluid, falling, closes an electric chain therefore the control lamp lights up.
The control lamp of "CHARGE" of red color, lights up at inclusion of ignition and to go out at once after launch of the engine. If the lamp burns at the working engine, so the generator does not charge the rechargeable battery.
The control lamp of "CHECK ENGINE" lights up at inclusion of ignition and to go out at once after launch of the engine. If the lamp burns at the working engine, so the control unit of the engine found malfunction.
The burning control lamp of "DOOR" specifies that one of doors of the car is not closed.
The control lamp of "OIL" lights up at inclusion of ignition and to go out at once after launch of the engine. If the lamp burns or blinks at the working engine, so oil pressure for lubricant of the engine is not enough.
The indicator of driving beam of headlights burns at the working engine and the turned-on driving beam of headlights.
The control lamp of low level of fuel specifies in the fuel tank that in a tank there was a reserve of fuel and the car it is necessary to fill as soon as possible.
The control lamp of the parking brake burns at the tightened parking brake and the included ignition.
The control lamp of "R-DEF" of a heater of back glass specifies that the heater of back glass works.
The control lamp of "BELTS" lights up and the sound signal at inclusion of ignition and not fastened forward seat belt is distributed.
The indicator of a signal of turn works synchronously with turn signal lamps.
On the dashboard the combination of devices, the central panel of finishing and a set of switches and control the device are placed.
The central panel represents a casing for the control panel of heating and ventilation, the radio receiver, a ware box and forms the basis for the lighter and an ashtray. The central panel can remain on the place at removal of the dashboard.
The control switch of illumination of salon allows to regulate dashboard illumination brightness.
The radio receiver is located in the central panel. The antenna and electric sockets for connection of the radio receiver are located in a back part of the radio receiver. The wire of the antenna passes under the dashboard and connects the antenna to the radio receiver. Before removal of the dashboard, the radio receiver needs to be removed.
The control panel of heating and ventilation is installed in the central panel. The control panel connects cables to a heater and regulates temperature and distribution of streams of air on interior of the car. For access to cables it is necessary to remove a part of the dashboard previously.
External rear-view mirror
The external rear-view mirror consists of a mirror, a frame (holder) of a mirror, the engine and a plait of wires with the socket. The provision of each external rear-view mirror can be adjusted in four directions remotely, from interior of the car.
System of the central control of locks of doors
1 – relay of the central control of locks of doors;
The system of the central control of locks of doors consists of locks of a door, internal and external handles of opening of locks, cylinders of locks and the switch of the central lock. The central locks are put on all doors of the car. The system becomes more active the switch located on the driver's door. The switch operates the relay which is located on the left side under the dashboard.
Each lock of a door has four drafts connecting the lock with internal and external to handles of opening of the lock of a door, the cylinder of the lock of a door and the internal button of blocking of the lock of a door. Pressing of the button of blocking of the lock of a door on the internal handle of a door locks and unlocks three doors of the car. Pressing of the button doors of the driver and a back door deduction of the external handle in open situation locks all four doors. Opening of this door a key, also opens locks of other doors.
Back doors has the blocking preventing opening of doors from interior of the car.
Window regulators with the electric drive
Window regulators with the electric drive provide a remote raising and lowering of glasses of forward and back doors. Each window regulator is put in action by the reversive electric motor. Engines of window regulators are run by the switches installed on forward and back doors. On a door of the driver the main switch which operates window regulators of all doors is installed.
Heater of back glass
Defrosting of back glass is carried out by a heater which represents a number of the parallel conductors which are raised dust on glass. At a transmission of electric current conductors heat up and defreeze and clean off back glass from moisture. Current moves from the relay located in the block of safety locks of a motor compartment. If glass on was purified in 15 minutes, it is necessary to include repeatedly a heater on the second cycle, i.e. for 15 minutes.
The front seat consists of a back of sitting and a pillow. Both seats have longitudinal adjustment and adjustment of a tilt angle of a seatback. The provision of a head restraint can be also adjusted or it can be removed from a seat.
The lever of adjustment of longitudinal provision of a seat is under the right or left forward angle of any forward sitting.
The handle for adjustment of a tilt angle of a seatback is located on a seat, from a door. For adjustment it is necessary to press the lever and, for lowering of a back, to acquire on it or for a back raising, to deviate (to exempt) from a back. After a lever otpuskaniye the provision of a back will be recorded.
The back seat consists of two separate back backs and one general pillow.
The pillow of a seat fastens on two locks put in a forward part of a pillow.
Two seatbacks are attached on arms with hinges.
Are enshrined by locks to the shock plates fixed нВ a body in the normal provision of a seatback.
The system of seat belts consists of five belts. Seat belts of the driver and side passengers I have three-point fastening. Seat belts of the driver are equipped with the alarm system which warns the driver ignition of a control lamp in a combination of devices and a sound signal. The prevention automatically stops approximately in 60 seconds.
Panels of an upholstery are formed from plastic and intended for finishing of an internal part of the car. It also promotes car sound insulation, and also closing of metal panels of a body.
The upholstery is established on all doors of the car, and also on racks and thresholds.
The trunk lid is attached to a body by two hinges. Two hinges are connected with each other by two springs and fixed by bolts. Springs help to open a trunk lid and support it in open situation.
The pro-thinned-out sealing strip fixed on a trunk lid ledge prevents course between a luggage carrier and a body.
The latch is attached in the center of the basis of a trunk lid. Adjustment of provision of a trunk lid is provided.
Screen wiper and washer of a windshield
The Sephia cars are equipped with a windshield screen wiper with a variable speed of cleaning.
The screen wiper consists of the engine of a screen wiper, drafts and two levers with brushes.
The washer of a windshield consists of a washer reservoir, the engine, two sprays and shlag. Both systems are connected with levers of a screen wiper and the timer in the combined switch of a steering column.
The switch of a screen wiper is located on a steering column.
The engine of a washer gives liquid on hoses to sprays. The engine works only with one frequency of rotation.
Sprays give liquid on a windshield and can be replaced separately.
The timer operates operating time of a screen wiper. It is an integral part of the combined switch of a steering column.
Drafts of a screen wiper connect the screen wiper engine to levers and consist of two rods and two blocks of a point of turn. The main function consists in transformation of rotary motion of a shaft of the engine into progress of brushes. At failure of any element, it is necessary to replace a screen wiper assembled.
The screen wiper engine – 2-speed, a direct current. The engine and an arm can be replaced separately from a screen wiper.